| Поиск по каталогу |
|
(строгое соответствие)
|
- Профессиональная
- Научно-популярная
- Художественная
- Публицистика
- Детская
- Искусство
- Хобби, семья, дом
- Спорт
- Путеводители
- Блокноты, тетради, открытки
The Effect of Heat Treatment on Rod Steel AISI 1045 and AISI 4140.
В наличии
| Местонахождение: Алматы | Состояние экземпляра: новый |
Бумажная
версия
версия
Автор: Nurul Amira Azmi
ISBN: 9783659469817
Год издания: 2014
Формат книги: 60×90/16 (145×215 мм)
Количество страниц: 84
Издательство: LAP LAMBERT Academic Publishing
Цена: 24061 тг
Положить в корзину
| Способы доставки в город Алматы * комплектация (срок до отгрузки) не более 2 рабочих дней |
| Самовывоз из города Алматы (пункты самовывоза партнёра CDEK) |
| Курьерская доставка CDEK из города Москва |
| Доставка Почтой России из города Москва |
Аннотация: Research in “Heat Treatment effect on Rod Steel AISI 1045 and AISI 4140”. This book is mainly covered the effect of heat treatment and continuous cooling treatment on two types rod steels, AISI 1045 and AISI 4140. Specimens were heated until 950°C and soaked for three hours in furnace. Then the specimens was cooled at different rate as indicated such as furnace cooled, air cooled, blowing air cooled, oil quenched, and water quenched. Hardness test, compress test and observed microstructure were performing on steels by using Rockwell Hardness Test, Universal Testing Machine and Scanning Electron Microscopy. By using water and oil quench, results will shows the hardness of the steels is increased after heat treatment. Continuous cooling treatment at different rate on steels will results formation of the martensite and decomposition of the microstructure.
Ключевые слова: heat treatment, HARDNESS TEST, AISI 1045, AISI 4140, compress test, vickers, microstructure transformation
Похожие издания
 | Отрасли экономики: Машиностроение Sarojini Jajimoggala,Shabana Shabana and Mohammed Abdul Shafeeq EFFECT OF HEAT TREATMENT ON ROLLING PERFORMANCE. Of Metal Matrix Composites. 1905 г., 68 стр., мягкий переплет Excellent qualities including low density, high plasticity, and ductility are found in aluminium and its alloys. Metal Matrix Composites (MMCs) are widely used in the domains of aviation, astronautics, autos, and high-speed trains due to their low density and inexpensive reinforcements. Because of its exceptional qualities, including high... | 25429 тг |
 | Отрасли экономики: Машиностроение Manu Sam and Radhika Nachimuthu Effect of Heat Treatment on Functionally Graded Copper Composite. A copper FGM for electric motor bearings. 2017 г., 80 стр., мягкий переплет A Functionally Graded Material (FGM) is an advanced material that is capable of producing gradation of its constituents throughout the component, utilising the fabrication technique and the density difference of its constituents. It has wide applicability in different industries in the present age, as this material could be developed with specific... | 21983 тг |
 | Отрасли экономики: Машиностроение Mohammed Al-Ghamdi Effect of Heat Treatment on Welded Aluminum. Effect of Heat Treatment on Mechanical Properties of ATIG Welded Aluminum Alloy. 2017 г., 56 стр., мягкий переплет The aim of this research was to investigate the effect of heat treatment on mechanical properties of 6063 aluminum alloy for a single pass of Activated Tungsten Inert Gas (ATIG) welding. and to determine the optimum parameters for heat treatment for the ATIG welded 6030 aluminum alloy. welded samples were tested for tensile strength and hardness.... | 21130 тг |