| Поиск по каталогу |
|
(строгое соответствие)
|
- Профессиональная
- Научно-популярная
- Художественная
- Публицистика
- Детская
- Искусство
- Хобби, семья, дом
- Спорт
- Путеводители
- Блокноты, тетради, открытки
Design, Fabrication and Testing of Heat Exchanger.
В наличии
| Местонахождение: Алматы | Состояние экземпляра: новый |
Бумажная
версия
версия
Автор: Jagdish Bhadu,Dr. Ashish Nayyar and Sarita Choudhary
ISBN: 9786200116994
Год издания: 2019
Формат книги: 60×90/16 (145×215 мм)
Количество страниц: 60
Издательство: LAP LAMBERT Academic Publishing
Цена: 24982 тг
Положить в корзину
| Способы доставки в город Алматы * комплектация (срок до отгрузки) не более 2 рабочих дней |
| Самовывоз из города Алматы (пункты самовывоза партнёра CDEK) |
| Курьерская доставка CDEK из города Москва |
| Доставка Почтой России из города Москва |
Аннотация: Demand for energy is growing day by day in the world. Due to limited resources and continuously growing demand there is an urgent need to utilize our finite resources carefully for a sustainable future. Our common goal is to achieve this task in the most efficient, cost effective, and least polluting manner. The energy available in the exhaust of many energy conversion devices goes as waste, if not utilized properly. Since exhaust gases of an internal combustion engine (ICE) carries away -about 30% of the heat of combustion, it represents a great potential to recover the conserve energy. In this project an energy conservation technology “waste heat recovery” is used. In this experimental work a waste heat operated counter flow type heat exchanger is developed to utilize the waste heat from the engine exhaust for heating. After developing the heat exchanger, experimental investigation is carried out for effectiveness of heat exchanger, effect on exhaust emissions and performance of the engine when heat exchanger is integrated with engine.
Ключевые слова: cogeneration, Emissions, Heat Exchanger, Specific fuel consumption, WASTE HEAT RECOVERY
Похожие издания
 | Sumit Sharma Instant-Cooling System in Vehicles. Design, Fabrication and Testing of Instant-Cooling Based Device. 2024 г., 52 стр., мягкий переплет In this book, design, fabrication and testing of instant-cooling system in vehicles is performed using liquid nitrogen. When the vehicle is parked in an open environment especially in summer season, the inner atmosphere gets warmer and results in human discomfort, it finds the solution as air– conditioner is used for reduction of human... | 26810 тг |
 | Отрасли знаний: Инженерные дисциплины -> Электротехника и электроника Chandrasekar P,PRABHU M.S and PRASANNAKUMAR INAMPUDI Fabrication of Next Generation Solar Cells. Design, Fabrication and Testing of Next Generation Dye Sensitized Solar Cells. 1905 г., 68 стр., мягкий переплет Among various photovoltaic technologies, Dye-Sensitized Solar Cells (DSSCs) have gained attention as an efficient and commercially viable option. DSSCs belong to the third generation of solar cells and have become a prominent research area within solar photovoltaics. They are particularly appealing due to their simpler fabrication procedures and... | 27379 тг |
 | Отрасли экономики: Машиностроение -> Автомобилестроение Milind Yadav Novel Variable Compression Ratio (VCR) Engine. Design, Fabrication and Testing. 2012 г., 152 стр., мягкий переплет Conventional gasoline engines work on the fixed compression ratio which is a golden mean between the knocking at high loads and fuel economy at low loads. A variable compression ratio engine can work at various compression ratios depending upon the vehicle performance needs. Engine downsizing, great fuel economy, no knocking operation and... | 38342 тг |
 | Отрасли экономики: Машиностроение Dinesh Kumara,Nanditha K. Hettiarachchi and D. M. R. Kumara Design, Fabrication and Testing of a Wind Turbine with Wind Deflectors. . 2017 г., 68 стр., мягкий переплет The overall objective of this research is to analyze the performance of the VAWT with wind deflectors and optimize the efficiency of the wind turbine and create a wind turbine which can perform in any area. The power in the wind is well known to be proportional to the cubic power of the wind velocity approaching a wind turbine. This means that... | 23152 тг |
 | Отрасли экономики: Машиностроение Manishkumar Gadle Design, Fabrication and Testing of Freezer-Free Domestic Refrigerator. . 2017 г., 120 стр., мягкий переплет This book has been designed as a reference for the undergraduate and post graduate students of engineering and technology and researchers. It provides a well balanced coverage of concepts, mathematical operations and demonstration within the scope of domestic refrigerator. The book covers the principles necessary for understanding the fundamentals... | 32397 тг |
 | Отрасли экономики: Машиностроение Haroun A.K. Shahad and Dhafer A.M. Hamzah Absorption and Adsorption Cooling Systems. Design Fabrication and Testing. 2016 г., 152 стр., мягкий переплет The world is facing a two fold crises now, shortage of conventional energy sources and environmental pollution. A lot of research is work needed to find new clean and sustainable energy source. Solar energy is the most abundant source of energy which is clean and sustainable but the the conversion efficiency of this energy into a more useful form... | 43045 тг |
 | Отрасли знаний: Общественные науки Yahiea Al-Naiemy Design, Fabrication, and Testing of Microstrip Antennas. . 2013 г., 52 стр., мягкий переплет In this book, a systematic approach for the design, fabrication and testing of antennas using Ink Jet Printing Technology (IJPT) is presented. The antennas are fabricated using DMP-2800 Dimatix FujiFilm Material Printer and Sliver Nano Particles (SNP) ink. The 3D electromagnetic simulation softwares CST MWS and HFSS are used to design the antennas... | 22584 тг |